Project Description

BOLE EKS

Hydraulic Servo Energy. Saving Injection Moulding Machine

Portfolio – Software

More than 60 technical upgrading in terms of mechanical , electrical ,hydraulic, software and assembling process. Originate from Germany design Plasticizing System, efficiency excess above 20% of domestic level

BOLE EKS

Intelligent

March into industry 4.0, opening a new era of intelligent factories

Intelligent networking management system.
High performance PLC of MMI, which getting information of the robot ,mold temperature controller, cooling water , machine accessories etc, realize data interaction, wireless networking management system. Besides, PC or cell phone terminal can always tell machine information, process parameters, operation status, failure situation and product analysis at a glance.order dispatched by computer ,which aims to working efficiency maximization, better product planning and operation control, production efficiency improvement .meanwhile ,we provide EMS data exchange terminal, making it possible to automate the whole line of the factory.

Stable

Structural rigidity increased by 30% with more than 60 technical innovations, excellent performance reaches to European standards

Accurate

Mold open&close positioning accuracy: ±0.5mm
Injection positioning accuracy: ±0.2mm
Injection weight accuracy: 3%

Economy

After sample survey, we conclude BOLE central clamping toggle design can save 2-5% material for 80% of customers’ mould, comparing to traditional edge clamping toggle design

CLAMPING UNIT

EKS centre clamping structure was design and stimulate by professional software. overall structure rigidity increased by 30%

bole dk clamping unit
  • New design ed EKS clamping structure.
    Bear averaged force, Less platen distortion, apply for more molds
  • 280-4000 Ton offer more spaces with built-in clamping cylinder compared with previous model
  • Patented pneumatic fast forced resetting connector, assemble & disassemble easily, adapted to all ejector structure
  • Optimized platen structure, easy to install compulsive ejector back rod
  • New Toggle structure, faster speed, more stable, short dry cycle time
  • T slot plus threaded hole platen, to avoid damage problem
  • Moving platen supporting structure:
    70-470 ton use linear guide instead of tie bar without lubrication to keep mold area clean. 550ton and above use non-slip foot design to make the machine more stable and reliable when heavy mold is loaded

Toggle System Comparison

BOLE

bole clamping comparison

BOLE centre clamping structure

  • 100% Clamping force efficiency
  • 2-5% Material saving
  • Reduces mold wear, platen deflection
  • Less possibility of flash, save flash trim work

Others

bole clamping comparison

Traditional Toggle system

  • 80-85% Clamping force efficiency
  • Moving platen with obvious deformation, causes flashes, waste of material and labor of trim the flashes

INJECTION UNIT

  • All series can fit with ABC screw,L/D ratio 23: I, to achieve the best plasticizing effect and efficiency
  • Originate form Germany design Plasticizing System, efficiency excess above 20% of domestic level
  • Upgrade module design, high rigidity injection seat, linear guide supporting structure
  • Enhanced cooling ring for barrel with temperature control, better charge efficiency
  • New injection cylinder ,lower injection oil back resistance
  • Strengthened charge unit, stable, long life
  • Compatible injection base for three different model
  • Custom made complicated technical requirement, applied to special plasticizing system

CONTROLLER

bole dk controller
  • EKS whole series configured with EV3 I IO PLC
    BL70-470EKS standard configured with IO inch PLC, KEBA bechoff is optional
    BL550EKS and above configured with 12 inch PLC, KEBA bechoff is optional
  • Equipped with 1/0 safety advice against short circuit
  • Servo system use CAN bus communication, increase system stability, visible motor energy consumption and inverter data
  • Unique hydraulic system for clamping combined with patent software, lead to repeatability precision
  • Main electric component use brand Schneider Eaton, ABB, Fuji, which ensure long service life
  • Independent Strong and weak wire layout, high anti interference, Independent electric control box structure, convenient for installation, examination and repair

HYDRAULIC UNIT

  • Standard I sets of core valve manifold for 2 joint, fast combined terminal.
    Optional: core pressure holding, one press for core pressure release, hot runner valve etc
  • Special hydraulic system for clamping with patent software algorithm, position accuracy to ( ±0.5mm)
  • Non welding hydraulic pipe system, avoiding oil leakage problem
  • Use low momentum servo system, quick response time (30-50ms), system pressure rise up to 17.5Mpa
    Injection pressure & speed increased greatly
  • Oil temperature auto control system, less cooling water consumption, machine more stable
bole dk controller

INTELLIGENT NETWORKING MANAGEMENT SYSTEM

March into industry 4.0, opening a new era of intelligent factories

High performance PLC of MM I, which getting information of the robot, mold temperature controller, cooling water , machine accessories etc, realize data interaction, wireless networking management system.
Besides, PC or cell phone terminal can always tell machine information, process parameters, operation status, failure situation and product analysis at a glance.
Order dispatched by computer, which aims to working efficiency maximization, better product planning and operation control, production efficiency improvement.
Meanwhile, we provide EMS data exchange terminal, making it possible to automate the whole line of the factory

Bole EKS intelligent network

TECHNICAL DATA

EKS SERIE
Download PDF
BOLE EKS

BL70EKS/C170

INJECTION UNIT
Screw specificationAA A B C
Screw diameter(mm)22 25 28 32
Screw ratio20 23 23 23
Injection capacity(cm3)55 71 89 117
Shot weight.PS(g)51 65 82 107
Injection rate(cm3/s)61 78 98 128
Injection pressure(MPa)318 246 196 150
Injection stroke145
Max. injection speed(mm/s)160
Screw speed(r/min)331
CLAMPING UNIT
Clamping force(kN)700
Opening stroke(mm)320
Space between tie bar(mm)360×330
Mould height min.(mm)140
Mould height max.(mm)370
Max. distance Platen(mm)690
Ejector stroke(mm)70
Ejector force forward(kN)31
Ejector force back(kN) 20
Number of ejector bar(PC) 5
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
9
Heater power(KW)
4.6 5.4 6.1 6.9
Nr. temp. control zones(PC)3+1
OTHER
Hoper capacity(Kg)25
Oil tank capacity(L)120
Weight(Ton)3.1
Dimensions (LxWxH)(m)3.8×1.2×1.7
ORÇAMENTO
BOLE EKS

BL100EKS/C340

INJECTION UNIT
Screw specificationAA A B C
Screw diameter(mm)28 32 36 40
Screw ratio20 23 23 23
Injection capacity(cm3)111 145 183 226
Shot weight.PS(g)102 133 168 208
Injection rate(cm3/s)78 102 130 160
Injection pressure(MPa)313 239 189 153
Injection stroke180
Max. injection speed(mm/s)127
Screw speed(r/min)280
CLAMPING UNIT
Clamping force(kN)1000
Opening stroke(mm)360
Space between tie bar(mm)410×360
Mould height min.(mm)160
Mould height max.(mm)420
Max. distance Platen(mm)780
Ejector stroke(mm)100
Ejector force forward(kN)31
Ejector force back(kN) 20
Number of ejector bar(PC) 5
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
9
Heater power(KW)
5.8 6.8 7.9 9
Nr. temp. control zones(PC)3+1
OTHER
Hoper capacity(Kg)25
Oil tank capacity(L)150
Weight(Ton)3.7
Dimensions (LxWxH)(m)4.2×1.22×1.85
ORÇAMENTO
BOLE EKS

BL140EKS/C460

INJECTION UNIT
Screw specificationAA A B C
Screw diameter(mm)32 36 40 45
Screw ratio20 23 23 23
Injection capacity(cm3)161 203 251 318
Shot weight.PS(g)148 187 231 292
Injection rate(cm3/s)105 133 164 208
Injection pressure(MPa)291 230 186 147
Injection stroke200
Max. injection speed(mm/s)131
Screw speed(r/min)280
CLAMPING UNIT
Clamping force(kN)1400
Opening stroke(mm)420
Space between tie bar(mm)460×410
Mould height min.(mm)180
Mould height max.(mm)470
Max. distance Platen(mm)890
Ejector stroke(mm)130
Ejector force forward(kN)45
Ejector force back(kN) 34
Number of ejector bar(PC) 5
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
13
Heater power(KW)
7.8 8.8 10 11.3
Nr. temp. control zones(PC)3+1
OTHER
Hoper capacity(Kg)25
Oil tank capacity(L)180
Weight(Ton)4.5
Dimensions (LxWxH)(m)4.8×1.35×1.85
ORÇAMENTO
BOLE EKS

BL170EKS/C630

INJECTION UNIT
Screw specificationAA A B C
Screw diameter(mm)36 40 45 50
Screw ratio20 23 23 23
Injection capacity(cm3)229 283 358 442
Shot weight.PS(g)211 260 329 406
Injection rate(cm3/s)114 141 178 220
Injection pressure(MPa)275 223 176 143
Injection stroke225
Max. injection speed(mm/s)112
Screw speed(r/min)215
CLAMPING UNIT
Clamping force(kN)1700
Opening stroke(mm)480
Space between tie bar(mm)510×460
Mould height min.(mm)200
Mould height max.(mm)530
Max. distance Platen(mm)1010
Ejector stroke(mm)150
Ejector force forward(kN)45
Ejector force back(kN) 34
Number of ejector bar(PC) 5
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
17
Heater power(KW)
11.2 12 13.2 14.4
Nr. temp. control zones(PC)3+1
OTHER
Hoper capacity(Kg)50
Oil tank capacity(L)230
Weight(Ton)6.5
Dimensions (LxWxH)(m)5.3×1.53×2.15
ORÇAMENTO
BOLE EKS

BL230EKS/C860

INJECTION UNIT
Screw specificationAA A B C
Screw diameter(mm)40 45 50 55
Screw ratio20 23 23 23
Injection capacity(cm3)314 397 491 594
Shot weight.PS(g)289 366 451 546
Injection rate(cm3/s)139 176 217 263
Injection pressure(MPa)277 219 177 147
Injection stroke250
Max. injection speed(mm/s)111
Screw speed(r/min)221
CLAMPING UNIT
Clamping force(kN)2300
Opening stroke(mm)530
Space between tie bar(mm)560×510
Mould height min.(mm)220
Mould height max.(mm)580
Max. distance Platen(mm)1110
Ejector stroke(mm)150
Ejector force forward(kN)62
Ejector force back(kN) 36
Number of ejector bar(PC) 9
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
21
Heater power(KW)
11.4 13 14.6 16.2
Nr. temp. control zones(PC)4+1
OTHER
Hoper capacity(Kg)50
Oil tank capacity(L)280
Weight(Ton)7
Dimensions (LxWxH)(m)5.8×1.55×2.15
ORÇAMENTO
BOLE EKS

BL280EKS/C1450

INJECTION UNIT
Screw specificationAA A B C
Screw diameter(mm)50 55 60 65
Screw ratio20 23 23 23
Injection capacity(cm3)569 689 820 962
Shot weight.PS(g)524 634 754 885
Injection rate(cm3/s)192 232 276 324
Injection pressure(MPa)256 211 178 151
Injection stroke290
Max. injection speed(mm/s)98
Screw speed(r/min)210
CLAMPING UNIT
Clamping force(kN)2800
Opening stroke(mm)580
Space between tie bar(mm)660×610
Mould height min.(mm)240
Mould height max.(mm)680
Max. distance Platen(mm)1260
Ejector stroke(mm)190
Ejector force forward(kN)62
Ejector force back(kN) 36
Number of ejector bar(PC) 13
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
27
Heater power(KW)
18.5 18.5 21 23
Nr. temp. control zones(PC)4+1
OTHER
Hoper capacity(Kg)50
Oil tank capacity(L)350
Weight(Ton)9
Dimensions (LxWxH)(m)6.4×1.58×2.2
ORÇAMENTO
BOLE EKS

BL350EKS/C2050

INJECTION UNIT
Screw specificationA B C D
Screw diameter(mm)60 65 75 80
Screw ratio23 23 23 21.3
Injection capacity(cm3)918 1078 1435 1633
Shot weight.PS(g)845 992 1320 1502
Injection rate(cm3/s)271 271 423 481
Injection pressure(MPa)226 193 145 127
Injection stroke325
Max. injection speed(mm/s)96
Screw speed(r/min)175
CLAMPING UNIT
Clamping force(kN)3500
Opening stroke(mm)660
Space between tie bar(mm)710×660
Mould height min.(mm)270
Mould height max.(mm)720
Max. distance Platen(mm)1380
Ejector stroke(mm)190
Ejector force forward(kN)62
Ejector force back(kN) 36
Number of ejector bar(PC) 13
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
42
Heater power(KW)
21.8 24 26.2 26.2
Nr. temp. control zones(PC)4+1
OTHER
Hoper capacity(Kg)50
Oil tank capacity(L)420
Weight(Ton)12.5
Dimensions (LxWxH)(m)6.9×1.75×2.25
ORÇAMENTO
BOLE EKS

BL470EKS/C3000

INJECTION UNIT
Screw specificationA B C D
Screw diameter(mm)70 75 85 90
Screw ratio23 23 23 21.5
Injection capacity(cm3)1423 1634 2099 2353
Shot weight.PS(g)1390 1503 1931 2164
Injection rate(cm3/s)361 361 532 597
Injection pressure(MPa)212 185 144 128
Injection stroke370
Max. injection speed(mm/s)94
Screw speed(r/min)164
CLAMPING UNIT
Clamping force(kN)4700
Opening stroke(mm)750
Space between tie bar(mm)810×760
Mould height min.(mm)300
Mould height max.(mm)820
Max. distance Platen(mm)1570
Ejector stroke(mm)220
Ejector force forward(kN)113
Ejector force back(kN) 75
Number of ejector bar(PC) 17
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
50
Heater power(KW)
27 29.2 31.4 31.4
Nr. temp. control zones(PC)4+1
OTHER
Hoper capacity(Kg)50
Oil tank capacity(L)500
Weight(Ton)17
Dimensions (LxWxH)(m)7.8x2x2.3
ORÇAMENTO
BOLE EKS

BL550EKS/C3700

INJECTION UNIT
Screw specificationA B C D
Screw diameter(mm)75 80 90 95
Screw ratio23 23 23 21.7
Injection capacity(cm3)1832 2085 2639 2940
Shot weight.PS(g)1686 1918 2428 2705
Injection rate(cm3/s)451 513 649 723
Injection pressure(MPa)204 179 142 127
Injection stroke415
Max. injection speed(mm/s)102
Screw speed(r/min)158
CLAMPING UNIT
Clamping force(kN)5500
Opening stroke(mm)850
Space between tie bar(mm)860×800
Mould height min.(mm)350
Mould height max.(mm)880
Max. distance Platen(mm)1630
Ejector stroke(mm)220
Ejector force forward(kN)113
Ejector force back(kN) 75
Number of ejector bar(PC) 17
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
17+42
Heater power(KW)
32 35.5 37.5 37.5
Nr. temp. control zones(PC)5+1
OTHER
Hoper capacity(Kg)100
Oil tank capacity(L)750
Weight(Ton)20
Dimensions (LxWxH)(m)8.5×2.2×2.6
ORÇAMENTO
BOLE EKS

BL650EKS/C4800

INJECTION UNIT
Screw specificationA B C D
Screw diameter(mm)80 85 90 100
Screw ratio23 23 23 21.8
Injection capacity(cm3)2286 2581 2893 3572
Shot weight.PS(g)2103 2374 2662 3286
Injection rate(cm3/s)510 576 646 798
Injection pressure(MPa)210 186 166 134
Injection stroke455
Max. injection speed(mm/s)102
Screw speed(r/min)153
CLAMPING UNIT
Clamping force(kN)6500
Opening stroke(mm)950
Space between tie bar(mm)960×860
Mould height min.(mm)400
Mould height max.(mm)1000
Max. distance Platen(mm)1950
Ejector stroke(mm)240
Ejector force forward(kN)152
Ejector force back(kN) 107
Number of ejector bar(PC) 21
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
17+50
Heater power(KW)
36 38.3 40.6 40.6
Nr. temp. control zones(PC)5+1
OTHER
Hoper capacity(Kg)100
Oil tank capacity(L)850
Weight(Ton)25
Dimensions (LxWxH)(m)9×2.3×2.7
ORÇAMENTO
BOLE EKS

BL750EKS/C5900

INJECTION UNIT
Screw specificationA B C D
Screw diameter(mm)80 90 100 110
Screw ratio23 23 23 21
Injection capacity(cm3)2512 3179 3925 4749
Shot weight.PS(g)2311 2925 3611 4369
Injection rate(cm3/s)532 532 832 1007
Injection pressure(MPa)236 186 151 125
Injection stroke500
Max. injection speed(mm/s)106
Screw speed(r/min)139
CLAMPING UNIT
Clamping force(kN)7500
Opening stroke(mm)1050
Space between tie bar(mm)1060×960
Mould height min.(mm)450
Mould height max.(mm)1100
Max. distance Platen(mm)1250
Ejector stroke(mm)270
Ejector force forward(kN)152
Ejector force back(kN) 107
Number of ejector bar(PC) 21
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
27+50
Heater power(KW)
43 48.5 54 59.5
Nr. temp. control zones(PC)5+1
OTHER
Hoper capacity(Kg)100
Oil tank capacity(L)1000
Weight(Ton)31
Dimensions (LxWxH)(m)9.8×2.7×2.7
ORÇAMENTO
BOLE EKS

BL850EKS/C7900

INJECTION UNIT
Screw specificationA B C D
Screw diameter(mm)90 100 110 120
Screw ratio23 23 23 21
Injection capacity(cm3)3465 4278 5177 6161
Shot weight.PS(g)3188 3936 4763 5668
Injection rate(cm3/s)666 822 995 1184
Injection pressure(MPa)230 186 154 129
Injection stroke545
Max. injection speed(mm/s)105
Screw speed(r/min)122
CLAMPING UNIT
Clamping force(kN)8500
Opening stroke(mm)1100
Space between tie bar(mm)1120×1020
Mould height min.(mm)450
Mould height max.(mm)1150
Max. distance Platen(mm)2250
Ejector stroke(mm)300
Ejector force forward(kN)212
Ejector force back(kN) 121
Number of ejector bar(PC) 21
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
50+50
Heater power(KW)
50 54.2 58.4 58.4
Nr. temp. control zones(PC)6+1
OTHER
Hoper capacity(Kg)100
Oil tank capacity(L)1200
Weight(Ton)40
Dimensions (LxWxH)(m)10.2×2.7×2.7
ORÇAMENTO
BOLE EKS

BL1000EKS/C10000

INJECTION UNIT
Screw specificationA B C D
Screw diameter(mm)100 110 120 130
Screw ratio23 23 23 21
Injection capacity(cm3)4671 5652 6726 7894
Shot weight.PS(g)4297 5199 6188 7262
Injection rate(cm3/s)820 820 1180 1385
Injection pressure(MPa)215 178 149 127
Injection stroke595
Max. injection speed(mm/s)104
Screw speed(r/min)114
CLAMPING UNIT
Clamping force(kN)10000
Opening stroke(mm)1150
Space between tie bar(mm)1160×1060
Mould height min.(mm)500
Mould height max.(mm)1200
Max. distance Platen(mm)2350
Ejector stroke(mm)300
Ejector force forward(kN)212
Ejector force back(kN) 121
Number of ejector bar(PC) 21
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
21+42+50
Heater power(KW)
56.2 60.4 62.4 62.4
Nr. temp. control zones(PC)6+1
OTHER
Hoper capacity(Kg)200
Oil tank capacity(L)1400
Weight(Ton)45
Dimensions (LxWxH)(m)11.3×3.1×3.9
ORÇAMENTO
BOLE EKS

BL1400EKS/C13500

INJECTION UNIT
Screw specificationA B C D
Screw diameter(mm)110 120 130 140
Screw ratio23 23 23 21.3
Injection capacity(cm3)6079 7235 8491 9847
Shot weight.PS(g)5593 6656 7811 9059
Injection rate(cm3/s)969 969 1353 1569
Injection pressure(MPa)221 186 158 137
Injection stroke640
Max. injection speed(mm/s)102
Screw speed(r/min)108
CLAMPING UNIT
Clamping force(kN)14000
Opening stroke(mm)1450
Space between tie bar(mm)1420×1220
Mould height min.(mm)650
Mould height max.(mm)1450
Max. distance Platen(mm)2900
Ejector stroke(mm)350
Ejector force forward(kN)227
Ejector force back(kN) 151
Number of ejector bar(PC) 29
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
42+50+50
Heater power(KW)
74.6 78.1 81.6 81.6
Nr. temp. control zones(PC)7+1
OTHER
Hoper capacity(Kg)200
Oil tank capacity(L)1650
Weight(Ton)67
Dimensions (LxWxH)(m)12.5×3.3×4.15
ORÇAMENTO
BOLE EKS

BL1600EKS/C19300

INJECTION UNIT
Screw specificationA B C D
Screw diameter(mm)120 135 145 155
Screw ratio23 23 23 21.4
Injection capacity(cm3)8195 10372 11966 13673
Shot weight.PS(g)7540 9543 11009 12579
Injection rate(cm3/s)1105 1105 1614 1844
Injection pressure(MPa)236 186 161 141
Injection stroke725
Max. injection speed(mm/s)98
Screw speed(r/min)101
CLAMPING UNIT
Clamping force(kN)16000
Opening stroke(mm)1550
Space between tie bar(mm)1520×1320
Mould height min.(mm)700
Mould height max.(mm)1550
Max. distance Platen(mm)3100
Ejector stroke(mm)400
Ejector force forward(kN)332
Ejector force back(kN) 256
Number of ejector bar(PC) 29
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
42+42+42+50
Heater power(KW)
70.7 76.5 80.7 80.7
Nr. temp. control zones(PC)7+1
OTHER
Hoper capacity(Kg)200
Oil tank capacity(L)2250
Weight(Ton)94
Dimensions (LxWxH)(m)13.8×3.56×4.3
ORÇAMENTO
BOLE EKS

BL2200EKS/C25000

INJECTION UNIT
Screw specificationA B C D
Screw diameter(mm)140 150 160 170
Screw ratio23 23 23 21.6
Injection capacity(cm3)12078 13865 15775 17809
Shot weight.PS(g)11112 12756 14513 16384
Injection rate(cm3/s)1361 1361 1778 2007
Injection pressure(MPa)214 186 164 145
Injection stroke785
Max. injection speed(mm/s)88
Screw speed(r/min)80
CLAMPING UNIT
Clamping force(kN)22000
Opening stroke(mm)1850
Space between tie bar(mm)1720×1520
Mould height min.(mm)750
Mould height max.(mm)1750
Max. distance Platen(mm)3600
Ejector stroke(mm)450
Ejector force forward(kN)425
Ejector force back(kN) 334
Number of ejector bar(PC) 33
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
42+50+50+50
Heater power(KW)
112.1 116.4 120.7 120.7
Nr. temp. control zones(PC)8+1
OTHER
Hoper capacity(Kg)400
Oil tank capacity(L)2500
Weight(Ton)132
Dimensions (LxWxH)(m)15.5×3.75×4.3
ORÇAMENTO
BOLE EKS

BL2500EKS/C36000

INJECTION UNIT
Screw specificationA B C D
Screw diameter(mm)160 170 185 195
Screw ratio23 23 23 21.7
Injection capacity(cm3)18589 20985 24852 27611
Shot weight.PS(g)17102 19306 22863 25402
Injection rate(cm3/s)1546 1546 2067 2296
Injection pressure(MPa)198 175 148 133
Injection stroke925
Max. injection speed(mm/s)77
Screw speed(r/min)68
CLAMPING UNIT
Clamping force(kN)25000
Opening stroke(mm)2000
Space between tie bar(mm)1820×1620
Mould height min.(mm)800
Mould height max.(mm)1850
Max. distance Platen(mm)3850
Ejector stroke(mm)500
Ejector force forward(kN)425
Ejector force back(kN) 334
Number of ejector bar(PC) 33
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
50+50+50+50
Heater power(KW)
175.8 180.7 188.7 188.7
Nr. temp. control zones(PC)8+1
OTHER
Hoper capacity(Kg)400
Oil tank capacity(L)2750
Weight(Ton)160
Dimensions (LxWxH)(m)17.5×3.95×4.5
ORÇAMENTO
BOLE EKS

BL2800EKS/C49000

INJECTION UNIT
Screw specificationA B C D
Screw diameter(mm)170 190 200 220
Screw ratio23 23 23 21.4
Injection capacity(cm3)23707 29614 32813 39704
Shot weight.PS(g)21811 27245 30188 36527
Injection rate(cm3/s)1700 1700 2354 2848
Injection pressure(MPa)209 167 151 125
Injection stroke1045
Max. injection speed(mm/s)75
Screw speed(r/min)69
CLAMPING UNIT
Clamping force(kN)28000
Opening stroke(mm)2100
Space between tie bar(mm)1920×1720
Mould height min.(mm)900
Mould height max.(mm)1950
Max. distance Platen(mm)4050
Ejector stroke(mm)500
Ejector force forward(kN)425
Ejector force back(kN) 334
Number of ejector bar(PC) 33
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
50+50+50+50+27
Heater power(KW)
22.7 233.7 239.5 239.5
Nr. temp. control zones(PC)8+1
OTHER
Hoper capacity(Kg)400
Oil tank capacity(L)3000
Weight(Ton)190
Dimensions (LxWxH)(m)18.6×3.95×5.1
ORÇAMENTO
BOLE EKS

BL3300EKS/C80000

INJECTION UNIT
Screw specificationA B C D
Screw diameter(mm)210 220 240 260
Screw ratio23 23 23 22
Injection capacity(cm3)41888 45973 54711 64210
Shot weight.PS(g)38537 42295 50334 59073
Injection rate(cm3/s)2940 2251 2940 3450
Injection pressure(MPa)190 174 146 124
Injection stroke1210
Max. injection speed(mm/s)65
Screw speed(r/min)60
CLAMPING UNIT
Clamping force(kN)33000
Opening stroke(mm)2200
Space between tie bar(mm)2110×1910
Mould height min.(mm)1000
Mould height max.(mm)2000
Max. distance Platen(mm)4200
Ejector stroke(mm)550
Ejector force forward(kN)565
Ejector force back(kN) 442
Number of ejector bar(PC) 25
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
50+50+50+50+42+42
Heater power(KW)
222.7 229.1 242.9 246
Nr. temp. control zones(PC)8+1
OTHER
Hoper capacity(Kg)400
Oil tank capacity(L)3500
Weight(Ton)265
Dimensions (LxWxH)(m)20.5×4.45×5.6
ORÇAMENTO
BOLE EKS

BL4000EKS/C120000

INJECTION UNIT
Screw specificationA B C D
Screw diameter(mm)220 240 260 270
Screw ratio23 23 23 22.1
Injection capacity(cm3)57751 68728 80660 86984
Shot weight.PS(g)53131 63230 74207 80026
Injection rate(cm3/s)2213 2213 3090 3333
Injection pressure(MPa)208 174 149 138
Injection stroke1520
Max. injection speed(mm/s)58
Screw speed(r/min)63
CLAMPING UNIT
Clamping force(kN)40000
Opening stroke(mm)2350
Space between tie bar(mm)1420×220
Mould height min.(mm)1100
Mould height max.(mm)2100
Max. distance Platen(mm)4450
Ejector stroke(mm)600
Ejector force forward(kN)565
Ejector force back(kN) 442
Number of ejector bar(PC) 25
DRIVING AND HEATING
Sys. Pressure(MPa)
17.5
Pump Motor(kW)
50+50+50+50+50+50
Heater power(KW)
246 259.8 274.8 274.8
Nr. temp. control zones(PC)8+1
OTHER
Hoper capacity(Kg)400
Oil tank capacity(L)4000
Weight(Ton)320
Dimensions (LxWxH)(m)22.5×4.65×6
ORÇAMENTO